Free Cisco 200-601 Exam Dumps Questions & Answers

ProfiNET has been disabled on a Cisco Industrial Ethernet switch. Which CLI command will correctly enable ProfiNET on the switch?

• A.switch(config)#vlan 10 profinet
• B.switch#enable profinet
• C.switch(config-if)#switchport profinet vlan 10
• D.switch(config)#profinet

You are a called upon to troubleshoot connectivity problems to a network device on a production floor. You have used ping and traceroute to verify that you cannot connect to the device from the management network. The network is 209.165.202.128/27 and the device has been given the IP address 209.165.202.158 and mask 255.255.255.224. You have verified that you can reach the device with your computer connected to the same switch as the device. What could be the cause of this problem?

• A.The device is set to the wrong IP address.
• B.The device is connected to a switchport in the wrong VLAN.
• C.The device is set to the wrong subnet mask.
• D.The device has no IP default gateway.

Refer to the exhibit.

You are required to implement traffic segmentation in the network. See the table for relevant device details:
L2SW4, L2SW5, and L2SW6 are connected to L3SW1 with 802.1Q trunks with VLAN 191 and VLAN 398 allowed on the trunk.
You have the following information from L3SW1:
L3SW1# show run interfaces
interface Vlan1
no ip address
shutdown
!
interface Vlan2
ip address 10.2.2.2 255.255.255.248
!
interface Vlan191
ip address 10.10.27.126 255.255.255.192
!
interface Vlan200
ip address 10.20.20.1 255.255.255.248
!
interface Vlan398
ip address 10.15.153.1 255.255.255.0
L3SW1# show ip route
*** Output Omitted ***
10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks
C 10.2.2.1/29 is directly connected, Vlan2
C 10.10.27.64/26 is directly connected, Vlan191
C 10.15.153.0/24 is directly connected, Vlan398
C 10.20.20.0/29 is directly connected, Vlan200
S 10.200.200.0/24 [1/0] via 10.20.20.2
S* 0.0.0.0/0 [1/0] via 10.2.2.1
You are required to implement a configuration that will meet the following connectivity requirements:
* The Administrator's Station must have full access to PanelView
* PanelView should have limited access, based on specific TCP ports, to PLC#1 and I/O#1
* The Administrator's Station should have no access to PLC#1 and I/O#1
* PLC#1 and I/O#1 should be able to communicate with each other on any port
Which action will allow you to meet the connectivity requirements?

• A.Put interface VLAN 191 and interface VLAN 398 into different Virtual Routing and Forwarding (VRF) instances on L3SW1
• B.Deploy an inbound ACL on interface VLAN 191 to control the traffic from the Administrator's Station and PanelView to PLC#1 and I/O#1
• C.Implement an ACL on Firewall1 to control the traffic flow between VLAN 191 and VLAN 398
• D.No change is required, the traffic is already limited appropriately by the VLAN segmentation

Which prompt is used to configure parameters for the Ethernet ports of an industrial switch?

• A.Switch(config-ind)#
• B.Switch(config-if)#
• C.Switch(config-vlan)#
• D.Switch(config-if-ind)#
• E.Switch(config-line)#

Which statement is correct regarding ProfiNET communication classes?

• A.ProfiNET-NRT is used to carry time critical status information
• B.ProfiNET-NRT is prioritized as Layer-2 Class-of-Service 1 (CoS 1)
• C.ProfiNET-RT traffic is carried in UDP and TCP packets
• D.ProfiNET-IRT requires switches with hardware time scheduling capabilities