Free EMC D-SNC-DY-00 Exam Dumps Questions & Answers


Exam Code/Number:	D-SNC-DY-00Join the discussion
Exam Name:	Dell SONiC Deploy Exam
Certification:	EMC
Free Question Number:	47
Publish Date:	Jan 13, 2026
# of views:	1071
Rating 100%

Page: 1 / 10
Total 47 questions

Question 1

Which two elements must be included in the show mclag interface x x command?

A.MC-LAG domain id
B.Peer-link port channel number
C.MC-LAG port channel number
D.MC-LAG VLAN id

Question 2

Refer to the exhibit.

What is the purpose of the static route?

A.Provide a route to the 12.0.0.0 network.
B.Provide a route to the 192.168.45.0 network.
C.Verify that devices in VLAN 45 are reachable.
D.Verify that the 12.0.0.0 network is active and reachable.

Question 3

VLAN 40 is configured in Switch A with an anycast-address of 192.168.40.254/24. The ARP neighbor suppression is enabled. Use the simulator to create a VTEP named vtep1 and assign an IP address of
10.10.10.1. Map the VNI 400 to VLAN 40.

Correct Answer:

see the explanation for all step by step solution with all explanation.
Explanation:
Here are the steps to create the VTEP and map the VNI to the VLAN:
* Enter Configuration Mode:
SwitchA# configure terminal
* Create VTEP Interface:
SwitchA(config)# interface vtep1
SwitchA(config-if-vtep1)# ip address 10.10.10.1/24
SwitchA(config-if-vtep1)# exit
* Map VNI 400 to VLAN 40:
SwitchA(config)# vlan 40
SwitchA(config-vlan)# vn-segment 400
SwitchA(config-vlan)# exit
* Enable ARP Neighbor Suppression:
SwitchA(config)# interface Vlan40
SwitchA(config-if-Vlan40)# ip address 192.168.40.254/24
SwitchA(config-if-Vlan40)# vxlan arp-suppression
SwitchA(config-if-Vlan40)# exit
* Save Configuration:
SwitchA# write memory
* Enter Configuration Mode:
* Begin by entering the global configuration mode to make changes to the switch configuration.
* Create VTEP Interface:
* Enter the interface configuration mode for the VTEP interface named vtep1 using interface vtep1.
* Assign the IP address 10.10.10.1/24 to the VTEP interface using the ip address command.
* Exit the interface configuration mode.
* Map VNI 400 to VLAN 40:
* Enter the VLAN configuration mode for VLAN 40 using vlan 40.
* Map the VNI 400 to VLAN 40 using the vn-segment 400 command.
* Exit the VLAN configuration mode.
* Enable ARP Neighbor Suppression:
* Enter the interface configuration mode for VLAN 40 using interface Vlan40.
* Assign the anycast IP address 192.168.40.254/24 to the VLAN interface using the ip address command.
* Enable ARP neighbor suppression using the vxlan arp-suppression command.
* Exit the interface configuration mode.
* Save Configuration:
* Save the configuration to ensure the changes persist after a reboot using the write memory command.
References:
* Dell Technologies Networking - SONiC
* Dell Enterprise SONiC Deployment Guide
These steps provide a comprehensive guide to configure a VTEP and map the VNI to VLAN 40 on Switch A, ensuring the specific requirements for IP addressing and ARP neighbor suppression are met.

Question 4

Which two things does the no vrrp 100 address-family ipv6 command delete?

A.Authentication
B.Identifier
C.Version
D.Address-family
E.Interface

Question 5

What are the supported modes for the QSFP28 ports on an S5248F?

A.1x100G, 1x40 G, 2x50 G, and 4x25 G
B.1x200G, 1x100 G, 1x40 G, and 4x25 G
C.1x100G, 1x40 G, 4x25 G, and 4x10 G
D.1x400G, 2x200 G, 4x25 G. and 4x10 G