Place the steps in the correct order to create clone copy sessions of device groups.

Correct Answer:

Explanation:
Here's the correct sequence of steps along with explanations:
Correct Order:
* Select Data Protection > Device Groups from the navigation pane.
* Why:This is the starting point within Unisphere for PowerMax. You need to navigate to the section where device groups are managed and where TimeFinder operations are initiated.
* Select a PowerMax array.
* Why:In an environment with multiple PowerMax arrays, you must specify the array on which you want to create the clone copy sessions.
* Select a group and click Create Pairs.
* Why:You are selecting the specific device group that will be the source for the clone operation and choosing the "Create Pairs" action to initiate the clone session creation process. This implies you are creating a clone from an existing group of devices.
* Select a source type and a target type.
* Why:This step defines the characteristics of the source and target devices for the clone session.
This could involve selecting from different storage groups, specifying thin or thick provisioning, or other relevant settings. Note that in a clone context, the "target type" often refers to how the clone will be linked to the source (e.g., a full copy or a linked target).
* Click Run Now to run the operation.
* Why:After configuring all the settings for the clone session, this action triggers the actual creation of the clone pairs based on the selected source and target types and other parameters.
* Click the TimeFinder Clone tab to view the list of clones.
* Why:Once the operation has been initiated, this is how you would verify that the clone sessions were created successfully and monitor their status.
* Select Data Protection > Device Groups from the navigation pane.
* Select a PowerMax array.
* Select a group and click Create Pairs.
* Select a source type and a target type.
* Click Run Now to run the operation.
* Click the TimeFinder Clone tab to view the list of clones.

Comment: *

Name: *

Email: *

Verification: *

A systems administrator plans to use Non-Disruptive Migration (NDM) to migrate data from a VMAX array running Enginuity 5876 to a PowerMax running PowerMaxOS 5978 Which NDM mode will be used?

• A.Metro-based
• B.Pass-through
• C.Asynchronous
• D.Adaptive Copy

Comment: *

Name: *

Email: *

Verification: *

A systems administrator created a secure snapshot using the -secure -delta 5:12 parameter. When can the snapshot be deleted?

• A.5 days and 12 hours after creation
• B.5 minutes and 12 seconds after creation
• C.5 hours and 12 minutes after creation
• D.Secure snapshots cannot be deleted

Comment: *

Name: *

Email: *

Verification: *

Place the steps to set Host Flags using the Create Host wizard in the correct order

Correct Answer:

Explanation:
Here's the correct sequence of actions, along with explanations:
Correct Order:
* Select the Hosts > Hosts menu option.
* Why:This is the initial navigation step within Unisphere. You need to go to the "Hosts" section where you can manage and configure host connections to the PowerMax array.
* Navigate to the storage array to be configured.
* Why:In an environment with multiple PowerMax arrays, you need to select the specific array for which you want to configure host settings.
* Click the Create button.
* Why:This initiates the "Create Host" wizard, which will guide you through the process of adding a new host and configuring its settings, including the host flags.
* Click the Set Host Flags button to override or enable any port flag settings.
* Why:Within the Create Host wizard, you'll reach a point where you can configure host flags.
Clicking the "Set Host Flags" button allows you to modify these flags.
* Host Flags:These flags are settings that define how the PowerMax array interacts with the host.
They control things like:
* SCSI support:Different variations of SCSI protocols.
* High availability:Features like auto-negotiation of failover.
* Other host-specific behaviors.
* Select the Hosts > Hosts menu option.
* Navigate to the storage array to be configured.
* Click the Create button.
* Click the Set Host Flags button to override or enable any port flag settings.

Comment: *

Name: *

Email: *

Verification: *

A non-production environment has been created with a VMFS Datastore named TestDS and a virtual machine named TestVM. SRDF/S has been configured between two PowerMax arrays One ESXi server is connected to the R1 device and another is connected to the R2 device. The VMFS Datastore resides on the R1 device.
The systems administrator wants to test the environment for disaster recovery readiness To simulate a disaster on the R1 side a graceful failover will be done. What is the correct sequence of steps on the R1 side of the test environment to perform a graceful failover?

Correct Answer:

Explanation:
1.Shunt down testvm on the primary esxi server
2. unregister testvm.
3.Unamount testds .
4.perform a failover operation.

Comment: *

Name: *

Email: *

Verification: *