An engineer must configure Linux hosts that are deployed on Cisco UCS B-Series Servers to boot from SAN. The SAN boot policy is configured in Cisco UCS Manager, and the boot order is verified to be set as expected However, the Linux hosts fail to boot. Which action resolves the issue?

• A.Remove all of the local storage that is installed
• B.Delete and reconfigure the boot LUN
• C.Delete and reconfigure the pWWN of the SAN boot target
• D.Remove all of the ISO images that are mounted as a virtual CD-ROM

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs. Which configuration set must be added to the script to fix the issue?

• A.switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
• B.switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli enable switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
• C.switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution
• D.switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1 switch(config-apple)# action 0.2 cli config t switch(config-apple)# action 0.5 cli switchto vdc Core switch(config-apple)# action 0.8 cli switchto vdc Distribution

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit. An engineer must connect N2K-Fex-1 and N5K-Core-1 so that the traffic flow between the two devices uses load balancing. After inspecting the statistics of the interconnecting interfaces, the engineer concludes that only one link is used. Which action resolves the problem?

• A.Configure each uplink to be a member of a separate LACP port channel.
• B.Configure the pinning max-link as 2.
• C.Configure destination-mac load balancing on N5K-Core-1.
• D.Configure source-destination load balancing on N5K-Core-1.

Comment: *

Name: *

Email: *

Verification: *

An attempt to use a global vNIC redundancy template pair results in a service profile that fails to apply. Which action resolves the issues?

• A.Assign the secondary template first, and then set the peer name.
• B.Assign the primary template first, and then set the peer name.
• C.Assign both templates simultaneously.
• D.Create the peer names before creating the templates.

Comment: *

Name: *

Email: *

Verification: *

Refer to the exhibit.

The HSRP configuration in the exhibit fails to function. Which action resolves this issue?

• A.Configure the same HSRP group on both devices.
• B.Enable IP redirects.
• C.Configure HSRP version 2.
• D.Set the MTU to 1500 bytes.

Comment: *

Name: *

Email: *

Verification: *