An LTM Specialist must perform a hot fix installation from the command line.
What is the correct procedure to ensure that the installation is successful?

• A.import the hot fix to the /var/shared/images directory
  check the integrity of the file with an md5 checksum
  tmsh install sys software hotfix <hotfix_name>.iso volume <volume_name>
• B.import the hot fix to the /var/shared/images directory
  check the integrity of the file with an md5 checksum
  tmsh apply sys software hotfix volume <volume_name> <hotfix_name>.iso
• C.import the hot fix to the /shared/images directory
  check the integrity of the file with an md5 checksum
  tmsh apply sys software hotfix volume <volume_name> <hotfix_name>.iso
• D.import the hot fix to the /shared/images directory
  check the integrity of the file with an md5 checksum
  tmsh install sys software hotfix <hotfix_name>.iso volume <volume_name>

Comment: *

Name: *

Email: *

Verification: *

What is a benefit provided by F5 Enterprise Manager?

• A.Enterprise Manager allows administrators to establish baseline application usage and generate an alert if an administratively set threshold for the application is exceeded.
• B.Enterprise Manager allows administrators to analyze traffic flow and create custom application IPS signatures.
• C.Enterprise Manager allows administrators to identify application vulnerabilities. Virtual patches are then automatically generated and applied to remediate the detected application vulnerability.
• D.Enterprise Manager allows administrators to monitor all application traffic. Configuration optimization suggestions based on the observed traffic patterns are then generated for the administrator to review and apply.

Comment: *

Name: *

Email: *

Verification: *

An LTM device is load balancing SIP traffic. An LTM Specialist notices that sometimes the SIP request is being load balanced to the same server as the initial connection.
Which setting in the UDP profile will make the LTM device more evenly distribute the SIP traffic?

• A.Disable Datagram LB
• B.Set Timeout to Indefinite
• C.Set Timeout to Immediate
• D.Enable Datagram LB

Comment: *

Name: *

Email: *

Verification: *

-- Exhibit-

-- Exhibit -
Refer to the exhibit.
An LTM Specialist configures a virtual server that balances HTTP connections to a pool of three application servers. Approximately one out of every three connections to the virtual server fails.
Which two actions will resolve the problem? (Choose two.)

• A.Enable SNAT automap on the virtual server.
• B.Verify that port lockdown is set to allow port 80.
• C.Increase the TCP timeout value in the default TCP profile.
• D.Verify the default gateway on the application servers.
• E.Assign a custom HTTP monitor to the pool.

Comment: *

Name: *

Email: *

Verification: *

A virtual server for a set of web services is constructed on an LTM device. The LTM Specialist has created an iRule and applied this iRule to the virtual server:
when HTTP_REQUEST {
switch [HTTP::uri] {
"/ws1/ws.jsp" {
log local0. "[HTTP::uri]-Redirected to JSP Pool"
pool JSP
}
default { log local0. "[HTTP::uri]-Redirected to Non-JSP Pool"
pool NonJSP
}
}
}
However, the iRule is NOT behaving as expected. Below is a snapshot of the log:
/WS1/ws.jsp-Redirected to JSP Pool
/WS1/ws.jsp-Redirected to JSP Pool
/WS1/ws.jsp-Redirected to JSP Pool
/WS1/WS.jsp-Redirected to Non-JSP Pool
/ws1/WS.jsp-Redirected to Non-JSP Pool
/WS1/ws.jsp-Redirected to JSP Pool
/ws1/ws.jsp-Redirected to Non-JSP Pool
What should the LTM Specialist do to resolve this?

• A.Select the "Process Case-Insensitivity" option for the virtual server.
• B.Use the followinG. switch [string tolower [HTTP::uri]]
• C.Set the "Case Sensitivity" option of each member to "None".
• D.Use the followinG. switch -lc [HTTP::uri]

Comment: *

Name: *

Email: *

Verification: *